TV Wall Mounting Byron Bay & Northern Rivers

TV Mounting Solutions for Every Setup

From a single bedroom TV to a full commercial installation, I handle all TV wall mounting across the Northern Rivers

Standard TV Wall Mount

Fixed, tilting, or full-motion bracket installation for TVs from 32 to 85 inches. Secure mounting into timber studs, brick, or concrete walls with all hardware included.

From $150

Cable Concealment

In-wall cable routing for plasterboard walls or surface-mounted cable channels for brick. Power point relocation behind the TV for a completely clean, wire-free look.

From $80 add-on

Soundbar Mounting

Wall-mounted soundbar installation below or above the TV. Bracket supplied or I install your manufacturer bracket. Clean cable management included.

From $60 add-on

Multi-Room TV Setup

Multiple TVs mounted throughout your home in one visit. Living room, bedroom, outdoor area, and home gym setups. Discounted rate for multi-TV jobs.

Contact for quote

Commercial TV Mounting

TV installation for restaurants, cafes, offices, gyms, and waiting rooms. Multiple screens, digital menu boards, and commercial display mounting across the Northern Rivers.

Contact for quote

Bracket Supply & Advice

Not sure which bracket you need? I carry a range of quality brackets for all TV sizes and can advise on the best option for your wall type and viewing angle.

Brackets from $40

Why Get Your TV Professionally Wall Mounted?

I mount TVs every week across Byron Bay, Ballina, Lismore, and the wider Northern Rivers. It is one of my most requested services and for good reason. A wall-mounted TV looks cleaner, saves floor space, and is safer in homes with kids or pets compared to sitting on a stand.

The problem is that TV mounting seems simple until you actually try it. You need to find the studs, make sure the bracket is level, ensure the wall can handle the weight, and deal with the cable mess. Get any of those wrong and you are looking at a crooked TV, a damaged wall, or worse, a TV that falls off the wall entirely.

I have mounted hundreds of TVs across the Northern Rivers on every type of wall you can imagine. I bring the right tools, the right brackets, and the experience to get it done properly in under an hour. No holes in the wrong spot, no wobbly mounts, no cables hanging everywhere.

Professional TV wall mounting service in Byron Bay showing clean cable concealment

Wall Types and What Matters for TV Mounting

Different walls need different approaches. Here is how I handle each type across Northern Rivers homes.

The type of wall you have is the single biggest factor in how a TV mounting job goes. Northern Rivers homes have a real mix of wall types depending on the age and style of the building, and each one needs a different approach. Here is what I deal with most often and how I handle each one.

Plasterboard Walls (Most Common)

Plasterboard is by far the most common wall type in Northern Rivers homes, especially anything built in the last 30 years. The key with plasterboard is that you cannot just screw a bracket into the plasterboard itself and hang a 25kg TV on it. The plasterboard will eventually give way and the TV will end up on the floor. What I need to do is locate the timber studs behind the plasterboard and mount the bracket into those. Studs are typically spaced at 450mm or 600mm centres, so I use a combination of a stud finder and a strong magnet to locate them precisely before drilling anything.

Sometimes the studs are not where you want the TV to sit. When that happens, I have a few options. For lighter TVs under about 15kg, I can use specialised plasterboard anchors like toggle bolts that spread the load across a larger area of plasterboard. For heavier TVs, I install a solid timber backing board that spans between two studs, which gives me a continuous mounting surface wherever I need it. This is a bit more work but it gives a rock-solid result and means the TV can go exactly where you want it rather than being dictated by stud positions.

Cable concealment in plasterboard walls is straightforward because I can cut neat holes above and below the TV and run the cables through the wall cavity. I install proper in-wall cable plates so the finish is clean and professional.

Brick and Block Walls

Older homes in Byron Bay, Bangalow, Lismore, and particularly the older streets of Ballina often have internal brick or block walls. Brick is actually excellent for TV mounting because it is incredibly strong and you can mount directly into it with masonry anchors. The downside is that drilling into brick is noisier, slower, and produces more dust than plasterboard work. I use a hammer drill with masonry bits and heavy-duty masonry sleeve anchors rated for the TV weight plus a generous safety margin.

Cable concealment on brick walls is different because you cannot run cables inside the wall cavity like you can with plasterboard. Instead, I use surface-mounted cable channels that stick to the wall and can be painted to match. These run from behind the TV down to the power point and AV equipment. It is not quite as invisible as in-wall routing but when done neatly and painted to match, most people barely notice them. For a completely concealed result on brick, I can chase a channel into the mortar joints and plaster over it, though this is more involved and adds to the cost.

Timber-Clad Walls

Timber-clad walls are common in the older Queenslander-style homes and weatherboard cottages around Mullumbimby, Federal, and the hinterland areas. The approach depends on whether the timber cladding has solid framing behind it. In most cases there are studs behind the cladding, and I can mount through the cladding into the studs. The key is making sure the cladding itself does not split when drilling. I pre-drill pilot holes and use appropriate screws that grip into the stud behind without cracking the timber boards.

For lightweight timber-clad walls without solid framing behind them, such as some internal partition walls in older homes, I may need to add a backing board or find an alternative mounting solution. I always assess the wall before committing to a mounting position and I will be upfront about what is and is not going to work safely.

Concrete Walls

Concrete walls are less common in residential properties around the Northern Rivers but they do come up in apartments, commercial spaces, and some modern builds. Concrete is the strongest wall material for TV mounting but it requires the right tools and fixings. I use a rotary hammer drill with SDS masonry bits and chemical anchor bolts or expansion anchors rated for the load. The result is extremely solid and there is zero chance of the TV coming off the wall. The trade-off is that concrete mounting takes longer and is noisier than other wall types.

Stud Finding and Weight Considerations

Getting the mounting right starts with understanding what is behind the wall and how much your TV weighs

This is where a lot of DIY TV mounting jobs go wrong. People grab a cheap stud finder from Bunnings, get an inconsistent reading, and drill into the wrong spot. Or they underestimate how heavy their TV is and use fixings that are not rated for the load. I see the results of both mistakes regularly and it is never pretty.

How I Find Studs

I use a combination of methods to locate studs accurately. My primary tool is a professional-grade electronic stud finder that detects changes in wall density, but I back this up with a rare-earth magnet that finds the screws or nails holding the plasterboard to the studs. The magnet method is extremely accurate because it pinpoints the exact centre of the stud. I also check by tapping the wall and listening for the change from hollow to solid, which gives me a rough guide before I confirm with the electronic tools. Once I have located the studs, I mark them with painter's tape so I can see exactly where to drill without leaving any marks on the wall.

TV Weight Categories

Modern TVs are lighter than people think, but they are still heavy enough that the mounting needs to be done properly. A 55-inch LED or OLED TV typically weighs between 12 and 18kg. A 65-inch model runs between 18 and 25kg. The big 75 to 85 inch screens can weigh 30 to 40kg or more. On top of the TV weight, you need to account for the weight of the bracket itself, which can add another 2 to 5kg depending on the type. A full-motion articulating bracket is heavier than a simple fixed mount because of all the moving parts and the extended arm.

I always check the TV weight against the bracket rating and the wall fixing capacity before mounting. The bracket needs to be rated for at least the TV weight, and ideally double it for a safety margin. The wall fixings need to be rated for the combined weight of the TV plus bracket plus any dynamic loads from adjusting a full-motion mount. I do not take shortcuts on this because the consequences of a TV falling off the wall are serious, both for the TV and for anyone standing underneath it.

Full-Motion vs Fixed vs Tilting Brackets

The type of bracket you choose affects the mounting requirements. A fixed bracket sits flat against the wall and distributes the weight evenly across the mounting points. This is the simplest and most secure option. A tilting bracket allows you to angle the TV down slightly, which is useful when the TV is mounted higher than eye level, such as above a fireplace. A full-motion or articulating bracket lets you pull the TV away from the wall, swivel it left and right, and tilt it, which is great for rooms where you watch TV from different positions. However, full-motion brackets put more stress on the mounting points because the TV is extended away from the wall on an arm, creating a lever effect. For full-motion brackets on plasterboard walls, I always mount into studs, no exceptions.

Multi-Room and Commercial TV Mounting

From home cinema setups to restaurant menu boards and gym displays

TV mounting is not just a living room thing anymore. I regularly mount TVs in multiple rooms throughout a home, and I do a fair bit of commercial work around the Northern Rivers too. Here is what is involved in larger installations.

Multi-Room Home Setups

A lot of my customers in Byron Bay and Ballina want TVs in the living room, master bedroom, kids' rooms, and sometimes an outdoor covered area like an alfresco or pool house. When I do multi-room jobs, I work through the house systematically so I am not moving tools and ladders between rooms more than necessary. Multi-room jobs are more cost-effective per TV because I am already on site with all my gear set up. If you are renovating or moving into a new home, this is the ideal time to get all your TVs mounted in one visit.

For outdoor TV mounting, I make sure the bracket and fixings are rated for outdoor use and that the TV is under a covered area. Direct sun and rain will destroy any TV, no matter how well it is mounted. I also make sure the power supply to the outdoor area is properly weatherproofed and that any cable runs are protected from moisture.

Commercial TV Installation

I mount TVs for businesses across the Northern Rivers including restaurants, cafes, pubs, offices, medical waiting rooms, real estate agencies, gyms, and retail shops. Commercial TV mounting often involves multiple screens and specific placement requirements for maximum visibility.

For restaurants and cafes in Byron Bay, I mount TVs for sports viewing, digital menu boards, and ambience screens. These need to be positioned for optimal viewing from multiple seating areas and mounted at heights that are visible over standing customers. I work with the business owner to find the best positions before drilling anything.

Gym TV mounting in places like Ballina and Byron Bay requires screens that are visible from cardio equipment, weight areas, and sometimes group fitness rooms. These are usually mounted high on the wall and angled downward so people can see them while exercising. I use commercial-grade tilting brackets for gym installations because they need to handle the vibration from the building as well as the weight of larger screens.

Office and waiting room TVs are usually simpler installations but they still need to look professional. I make sure all cables are concealed, the screen is perfectly level, and the placement suits the room layout. For real estate agencies and medical practices, I often mount screens in reception areas and consultation rooms.

For any commercial installation, I can work outside business hours so there is no disruption to your operations. I have done early morning and weekend installs for businesses that cannot afford downtime during trading hours.

What I Bring to Every TV Mounting Job

I turn up fully equipped so the job gets done in one visit with no return trips

One of the things that sets a professional TV mounting apart from a DIY attempt is having the right gear. I bring everything needed to mount your TV on my first visit, regardless of the wall type or TV size. Here is what is in the van.

Brackets and Hardware

I carry a range of quality TV brackets in fixed, tilting, and full-motion configurations suitable for TVs from 32 to 85 inches. All brackets I supply are rated well above the weight of the TVs they are designed for. I also carry the full range of wall fixings including timber screws, plasterboard toggles, masonry sleeve anchors, chemical anchors, and expansion bolts. Whatever wall type you have, I have the right fixings on the van.

If you have already purchased your own bracket, that is perfectly fine. I will check it is suitable for your TV and wall type before installing it. If there is an issue with the bracket you have bought, I will let you know upfront rather than installing something that is not going to do the job safely.

Tools

I carry a professional cordless drill and impact driver, a hammer drill for masonry, a full set of drill bits for every wall type, a professional electronic stud finder, rare-earth magnets, a laser level for perfect alignment, spirit levels, a cable-pulling kit for in-wall cable routing, hole saws for cable plate cutouts, and all the hand tools needed for the job. I also carry a portable vacuum to clean up any drilling dust as I go so your home stays clean.

Cable Management Supplies

For cable concealment jobs, I carry in-wall cable plates in various styles, surface-mounted cable channels in white and paintable finishes, cable ties, velcro straps, and conduit for longer cable runs. If you need a power point relocated behind the TV, I can advise on the best approach and connect you with a licensed electrician for the electrical work, or I can install a cable management solution that neatly routes the power cable to the nearest existing power point.

The bottom line is that when I turn up, I have everything needed to complete the job. No running to Bunnings halfway through, no asking you to buy extra parts, no return visits. One appointment, one visit, job done.

TV Wall Mounting Cost Guide for Northern Rivers

Transparent pricing so you know what to expect before I arrive

I believe in being upfront about costs. TV wall mounting pricing depends on a few factors including the TV size, wall type, whether you need cable concealment, and whether I am supplying the bracket. Here is a general guide to help you budget for the job.

Standard TV Mounting

A basic TV wall mount on a plasterboard wall with timber studs, using a fixed or tilting bracket, typically ranges from $150 to $250 depending on the TV size. This includes locating studs, mounting the bracket, hanging the TV, and making sure everything is level and secure. If you are supplying your own bracket, the cost is at the lower end. If I supply the bracket, the bracket cost is added on top.

Cable Concealment Add-On

In-wall cable concealment on plasterboard walls adds $80 to $150 to the job depending on the complexity. A simple HDMI and power cable run from the TV to the AV unit below is at the lower end. More complex setups with multiple cables, longer runs, or power point relocation recommendations are at the higher end. Surface-mounted cable channels on brick walls start from around $60.

Soundbar Mounting Add-On

Mounting a soundbar below or above the TV typically adds $50 to $80 depending on the soundbar type and mounting method. If the soundbar uses its own wall bracket system, it is straightforward. If it needs a separate universal bracket, there is a small additional cost for the bracket itself.

Brick and Concrete Wall Premium

Mounting on brick or concrete walls takes longer and requires specialist fixings, so there is typically a $50 to $100 premium over standard plasterboard mounting. This reflects the additional time for masonry drilling and the cost of heavy-duty masonry anchors.

Multi-TV Discounts

If you have multiple TVs to mount in one visit, the per-TV cost drops because I am already on site with all my gear. A second TV in the same visit is usually discounted by $30 to $50 off the standard rate. For commercial jobs with three or more screens, I provide a package quote that reflects the efficiency of doing everything in one session.

For an exact quote on your specific setup, call me on 0481 457271 or text me a photo of the wall and your TV model. I will get back to you with a firm price within the hour. No surprises, no hidden costs. You can also check out my other handyman services or read about my furniture assembly service if you have other jobs to bundle in.

Common TV Mounting Mistakes I Fix

The jobs that start with someone saying "I thought I could do it myself"

I reckon about a third of my TV wall mounting jobs in Byron Bay and the Northern Rivers are actually fixing someone else's attempt. There is no shame in it. TV mounting looks straightforward until you are standing there with a drill in one hand, a 30kg TV on the floor, and a bracket that does not seem to line up with anything. Here are the most common mistakes I see and fix on a regular basis.

Screwing Brackets Straight into Plasterboard Without Studs

This is the number one mistake and it is the most dangerous one. I get calls from people in Ballina, Byron Bay, Lennox Head, and all over the Northern Rivers who have screwed a TV bracket directly into plasterboard using the plastic wall plugs that came in the box. It holds for a day or a week, and then one morning they walk into the living room and the TV is on the floor with a chunk of plasterboard ripped out of the wall.

Plasterboard on its own cannot support a heavy TV. A standard 55-inch TV weighs around 15 to 20kg, and a 65-inch is often 25kg or more. Add a full-motion bracket that extends out from the wall and you have significant leverage forces pulling on those fixings. Cheap plastic wall plugs in plasterboard are rated for maybe 5 to 10kg in ideal conditions, and that is a static, downward load, not a TV cantilevered off the wall on an articulating arm. The plasterboard will crumble around the plug and the whole thing comes down.

When I fix these jobs, I patch the damaged plasterboard, locate the timber studs properly, and remount the bracket into solid timber. If the studs are not in the right position, I install a backing board between studs to create a proper mounting surface. It costs a bit more than doing it right the first time because I have to repair the wall damage as well, but the TV ends up secure and the customer can stop worrying about it falling on their kids or their dog.

Using the Wrong Size or Type of Bracket

Not all TV brackets are created equal and not all brackets fit all TVs. I regularly see TVs hanging on brackets that are either too small for the TV, not rated for the weight, or have the wrong VESA pattern. The VESA pattern is the spacing of the mounting holes on the back of your TV, and it needs to match the bracket. A bracket designed for a 32-inch TV should not be holding up a 65-inch panel, even if you managed to get the bolts to line up.

I also see cheap brackets from online marketplaces that claim to fit everything from 32 to 75 inches. Some of these are fine. Some are flimsy steel that flexes under the weight of a large TV. When I supply brackets, I use quality brands that are properly rated and tested. When a customer has already bought a bracket, I check the weight rating, the VESA compatibility, and the overall build quality before I put it on the wall. If it is not up to the job, I will tell you straight rather than install something I am not confident in.

Cables Dangling Down the Wall

You have spent money on a nice TV and a proper wall mount and then there is a tangle of HDMI cables, power cords, and aerial leads hanging down the wall in full view. It looks terrible and it undoes the whole point of wall mounting, which is to get that clean, modern look. I see this constantly on TV mounting jobs across Byron Bay and the Northern Rivers, especially when people have mounted the TV themselves and not thought about what to do with the cables.

The fix depends on the wall type. On plasterboard walls, I run cables inside the wall cavity using proper in-wall cable plates. You get two neat wall plates, one behind the TV and one down near the power point, with nothing visible in between. On brick or concrete walls where in-wall routing is not practical, I install surface-mounted cable channels that follow the wall down from the TV to the entertainment unit. These channels can be painted to match the wall colour and once painted, most people do not even notice them. Either way, it takes an extra 30 to 60 minutes and the result is a massive improvement. If you need a power point relocated behind the TV, I can coordinate with a licensed electrician to make that happen as well. For more about my approach to keeping things neat, check out my general handyman services page.

TVs Mounted Way Too High on the Wall

This is a classic DIY mistake and it is one that a lot of people do not realise is a problem until they have been watching TV with a sore neck for six months. The ideal viewing height has the centre of the TV screen roughly at eye level when you are seated on your couch. For most lounge setups, that means the bottom of the TV should be about 60 to 80 centimetres from the floor, depending on the TV size and your couch height.

What I see instead is TVs mounted at standing eye height or even higher, with the centre of the screen at 150cm or more off the floor. People do this because it feels right when they are standing there holding the bracket, or because they have seen TVs mounted high in pubs and restaurants. But a pub mounts TVs high so you can see them from across the room while standing at the bar. Your living room in Bangalow or Ocean Shores is a different story. You are sitting down, probably reclined slightly, and your natural eye line is much lower than you think.

When I mount a TV, I always discuss the viewing position with the customer before I drill a single hole. I sit on the couch, work out the natural eye line, and mark the mounting height accordingly. If a tilting bracket is needed to angle the TV down slightly, I recommend one. Getting the height right makes a huge difference to viewing comfort and it is one of those details that separates a professional installation from a DIY job.

No Cable Management Plan at All

Related to the dangling cables problem, some people mount the TV without thinking about where the power, HDMI, and other connections are going to come from. The power point is on the wrong wall, the Foxtel box is in a cabinet on the other side of the room, or the aerial point is two metres away from where the TV now sits. They end up with extension leads running across the skirting board, cables draped over furniture, and a setup that is messy and potentially a trip hazard.

Before I mount any TV, I talk through the full setup with the customer. Where is the power point? Where is the aerial or network connection? Where will the streaming devices, game consoles, and sound systems sit? I plan the cable routes before I pick up the drill, and I make sure everything can be connected neatly. Sometimes that means recommending a different wall position for the TV, or suggesting a wireless HDMI transmitter if the source devices are far away. A bit of planning upfront saves a lot of mess and frustration down the track.

If any of this sounds familiar, do not stress. Give me a call on 0481 457271 and I will come out, assess the situation, and get your TV mounted properly. Whether it is a new installation or fixing a previous attempt, I have seen it all and I will get it sorted. I also handle shelf installation and blind and curtain fitting if you have other jobs to bundle in while I am there.

Frequently Asked Questions

How much does TV wall mounting cost in Byron Bay?

TV wall mounting in Byron Bay typically ranges from $150-$350 depending on the TV size, wall type, and whether you need cable concealment. A standard fixed mount on a timber stud wall for a 55-65 inch TV is at the lower end. Larger TVs on plasterboard or brick walls with full cable concealment cost more. Call 0481 457271 for a quote on your specific setup.

Can you mount a TV on a plasterboard wall?

Yes, TVs can be mounted on plasterboard walls but the method depends on the TV weight. For lighter TVs, heavy-duty plasterboard anchors can work. For heavier TVs, mounting into the timber studs behind the plasterboard is essential. I use a stud finder and magnet to locate studs precisely. If studs are not in the right position, I can install a backing board between studs for a solid mounting surface. Call 0481 457271 to discuss your wall type.

Do you supply TV brackets or do I need to buy one?

I can supply brackets or install one you have already purchased. I carry a range of fixed, tilting, and full-motion brackets that suit most TV sizes from 32 to 85 inches. If you have already bought a bracket, I am happy to install it. I will check the bracket is rated for your TV weight and VESA pattern before starting. Call 0481 457271 and let me know your TV model so I can advise.

Can you hide the cables when mounting my TV?

Yes, cable concealment is one of the most popular add-ons to a TV mounting job. For plasterboard walls, I run cables inside the wall cavity using in-wall cable plates for a completely clean look. For brick or concrete walls, I use surface-mounted cable channels that are colour-matched to the wall. I can also arrange a power point behind the TV so there are no cables visible at all.

How long does it take to wall mount a TV?

A standard TV wall mount on a timber stud wall takes about 45 minutes to an hour. With cable concealment, allow 1.5 to 2 hours. Brick or concrete walls take longer due to masonry drilling, so allow 1 to 1.5 hours for the mount alone. Multi-room setups or commercial installations with multiple TVs are quoted individually. Call 0481 457271 for a time estimate.

Do you mount soundbars and set up the TV after mounting?

Yes, I mount soundbars below or above the TV as part of the installation. I also do basic TV setup after mounting, including connecting to your aerial, Foxtel, Fetch, Apple TV, or streaming device, and making sure the picture is working. I will get the TV on the wall, connected, and working before I leave. Call 0481 457271 to book.

TV Wall Mounting Services Northern Rivers